Andes Workshop
https://forum.andestech.com/

AndeSight v5.0.0 Quick Start Guide
https://forum.andestech.com/viewtopic.php?f=6&t=1049
Page 1 of 1

Author:  Niraj Dengale [ Tue Jan 04, 2022 2:56 pm ]
Post subject:  AndeSight v5.0.0 Quick Start Guide

Please follow the steps below to get started with AndeSight IDE.

Installation
-------------

Execute the AndeSight STD v5.0 installer to invoke the installation wizard:
1. To install AndeSight STD v5.0 on Windows, find the installer Setup.exe under the directory INSTALLER_ROOT\Windows\Disk1 and double-click it.

To install AndeSight STD v5.0 on Linux, find the installer Setup.sh under the directory INSTALLER_ROOT/[Linux_x64|Linux_x86]/Disk1/ and execute it by issuing the following command in the console:
$ ./Setup.sh
Attachment:
1.jpg
1.jpg [ 33.82 KiB | Viewed 4860 times ]


2. Follow the installer instructions to install AndeSight.
In license type selection page, please choose "Activation code" to finish installation.
Attachment:
2.jpg
2.jpg [ 29.42 KiB | Viewed 4860 times ]


Product activation
--------------------

Choose the license type for your use of AndeSight v5.0.0 IDE and click “Next".

1. Double-click the desktop shortcut or the file “AndeSight.exe” under AndeSight_ROOT\ide to launch the AndeSight IDE.

2. A dialog pops out to remind you that no license is installed yet. Click the “Install now…” button to open activation window.
Attachment:
3.jpg
3.jpg [ 21.99 KiB | Viewed 4860 times ]


3. In the invoked dialog, enter a valid activation code received from Andes Technology Corporation. Then, click “Deploy Activation code” or the “OK” Button.
Attachment:
4.jpg
4.jpg [ 41.39 KiB | Viewed 4860 times ]


Run first project
-------------------

1. Find the Andes Project Creator view on the launched AndeSight IDE. Select a connection configuration and a project language. Then, expand a group in the Chip Profile section and double-click the desired chip profile.
Attachment:
5.jpg
5.jpg [ 90.42 KiB | Viewed 4860 times ]


2. A dialog box opens. Enter a project name and select a project type and toolchain. Then, click the “Finish” button.
Attachment:
6.jpg
6.jpg [ 41.04 KiB | Viewed 4860 times ]


3. Select the created project folder in the Project Explorer view and click "Build" icon on the AndeSight toolbar to compile the program, as shown in below picture.
Attachment:
7.jpg
7.jpg [ 61.12 KiB | Viewed 4860 times ]


4. Check the compilation results in the Console view and verify that an executable has been generated in the PROJECT/Debug folder.
Attachment:
8.jpg
8.jpg [ 104.35 KiB | Viewed 4860 times ]


5. Click "Debug As" --> "Application Program"
Attachment:
9.jpg
9.jpg [ 78.9 KiB | Viewed 4860 times ]


6. After a debug session is launched, click the toolbar buttons in the Debug view to observe the results in other views (the Variables view, the Registers view ...)
Attachment:
10.jpg
10.jpg [ 113.03 KiB | Viewed 4860 times ]


7. The output will be displayed in the console view.
Attachment:
11.JPG
11.JPG [ 37.07 KiB | Viewed 4860 times ]

Page 1 of 1 All times are UTC + 8 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/