Andes Workshop
http://forum.andestech.com/

AndeSight Startup Guide for N22
http://forum.andestech.com/viewtopic.php?f=6&t=1047
Page 1 of 1

Author:  Niraj Dengale [ Thu Jun 13, 2019 8:42 pm ]
Post subject:  AndeSight Startup Guide for N22

Please follow the steps below to get started with AndeSight STD

Installation
-------------

1. Double click setup.exe to install AndeSight from install directory.
Attachment:
setup.jpg
setup.jpg [ 66.13 KiB | Viewed 34042 times ]


2. Follow the installer instructions to install AndeSight.
In license type selection page, please choose "Activation code" to finish installation.
Attachment:
activation_type.jpg
activation_type.jpg [ 62.02 KiB | Viewed 34042 times ]


Product activation
--------------------

1. Double-click the desktop shortcut or the file “AndeSight.exe” under AndeSight_ROOT\ide to launch the AndeSight IDE.

2. A dialog pops out to remind you that no license is installed yet. Click the “Install now…” button to open activation window.
Attachment:
license.jpg
license.jpg [ 54.19 KiB | Viewed 34042 times ]


3. In the invoked dialog, enter a valid activation code received from Andes Technology Corporation. Then, click “Deploy Activation code” or the “OK” Button.
Attachment:
prod_activation.jpg
prod_activation.jpg [ 71.79 KiB | Viewed 34042 times ]


4. A dialog box containing license information pops up next. Click “OK” to complete the license activation.
Attachment:
prod_activated.jpg
prod_activated.jpg [ 97.47 KiB | Viewed 34025 times ]


Run first project
-------------------

1. To import a demo project, go to "File -> Import..." and then select "Existing Projects into Workspace"
Attachment:
import_proj.jpg
import_proj.jpg [ 55.45 KiB | Viewed 34042 times ]


2. The demo projects are under "AndeSight_ROOT/demo" directory.
Attachment:
import.jpg
import.jpg [ 93.02 KiB | Viewed 34042 times ]


3. After selecting a demo project, click "Finish" on the Import wizard.
Attachment:
import_printf.jpg
import_printf.jpg [ 73.95 KiB | Viewed 34042 times ]


4. Right click on the project folder and choose "Target Configuration" and choose "Simulator/ICE" as target.
Attachment:
toolchain_1.JPG
toolchain_1.JPG [ 107.39 KiB | Viewed 33978 times ]


If the hardware package you are using is Fixed-configuration N22, please follow the additional two steps as mentioned below:
i] Click on the "browse" button in "Chip Profile" to invoke the "Select Target" dialog box.
Users should change the toolchain for Starup demos from "nds32le-elf-mculib-v5" to "nds32le-elf-mculib-v5e".
Attachment:
toolchain_2.JPG
toolchain_2.JPG [ 68.78 KiB | Viewed 33978 times ]

ii] Please add the following options into SID Misc Arguments of Target Configuration:
-e " set cpu cpu-option \\" --conf-isa-e on --conf-pmp 0 --conf-pfm off --conf-powerbrake off --conf-icache off --conf-user-mode off --conf-mul radix4 --conf-btb off \\""
Attachment:
target_config.JPG
target_config.JPG [ 125.63 KiB | Viewed 33978 times ]


5. Right click on the project folder and select "Build Project" to build.
Attachment:
build.jpg
build.jpg [ 65.64 KiB | Viewed 34042 times ]


6. Check the compilation results in the Console view and verify that an executable has been generated in the PROJECT\Debug folder.
Attachment:
build_result.jpg
build_result.jpg [ 225.81 KiB | Viewed 34042 times ]


7. Right click on project directory and select "Run As" --> "Application Program"
Attachment:
run.jpg
run.jpg [ 151.73 KiB | Viewed 34042 times ]


8. The output will be displayed in "UART2" under "Target Manager".
Attachment:
result.jpg
result.jpg [ 61.19 KiB | Viewed 34042 times ]

Page 1 of 1 All times are UTC + 8 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/